Menu

PDF version

Technical Data Sheet (TDS)

BCF-828 Commercial Carpet Adhesive Fast Set

Ultimate Commercial Carpet Adhesive

Special features

  • Aggressive tack, superior green strength, versatile, and trouble free
  • For the heaviest commercial applications: latex and urethane unitary, urethane attached cushion, hot melt, woven polypropylene (ActionBac®), woven, polyurethane laminate and other commercial backings including double glue-down
  • Excellent re-tack

Product Description
BCF-828 The Ultimate Adhesive is specially formulated to handle your toughest installation challenges and has been formulated to ensure adhesive perrformance under the very demanding conditions commonly found in today?s fast paced construction.
This firm setting, fast tacking adhesive is excellent for "double glue down" installations, woven carpets, and carpets with stiff unitary backing or attached cushions. BCF-828 is a safe, light colored, low odor, latex based adhesive designed with the installer's needs in mind. BCF-828 is moisture resistant and nonflammable, and is the most versatile, strongest, and most trouble-free floor covering adhesive. This adhesive is backed by a CleanGuard® two-stage antimicrobial. CleanGuard is a specifically formulated broad-spectrum, anti-microbial agent that protects our adhesives and sealers from microorganisms, such as mold or mildew, in both wet and dry state.
BCF-828 Ultimate Adhesive can be used for the following carpet backings and floor coverings:
- Direct-Glue: woven polypropylene (ActionBac®, hot melt, etc.) latex unitary, polyurethane foam-backed (Enhancer® I,II,III,IV, BioCel? and Durafoam), rubber backs, woven, axminster, needlepunch, and jute
- Double-Glue: BCF-828 is recommended for double-glue "carpet to pad" applications with specific carpet backings approved by STAUF for this application. This adhesive can also be used to adhere approved double-glue carpet cushions.
Note: This adhesive is not recommended for vinyl backed (PVC) sheet goods or carpets.
Pre-Installation Checklist
A successful installation requires proper preparation of the sub floor. Read and understand all applicable guidelines and technical data sheets before installation. Follow industry standards and flooring manufacturer's recommendations for sub floor moisture content, design, layout and application of flooring materials. All slab constructions must meet the specific requirements of the floor covering to be installed.
Sub Floor Examination
Prior to installation, the sub floor must be checked according to applicable installation guidelines. It must be solid and sound, flat, permanently dry, clean, free of chaps, indentations and anti-adherents, as well as resistant to pressure and tension. Moisture content of all floors must be measured before installation.
Moisture content in concrete sub floors must be below 8#/24hrs/1,000 sq. ft. using the Calcium Chloride Test or less than 85% RH using the in-situ test per ASTM F1869 and F2170.

Sub Floor Preparation
Depending on type and condition of sub floor, a mechanical treatment (e.g. mechanical brushing, grinding or sanding) may be required. Intensity of such work must be determined at the site by the installer. Dust, paint, residual adhesives or other surface contaminants must be removed by suitable means. Cleaning the surface with an industrial vacuum cleaner is recommended. Cracks and gaps must be filled with concrete crack filler unless they are expansion joints. Level when necessary to 3/16 inches within 10 feet. Heated sub floors must be primed.
Installation Procedure
Spread the adhesive with the appropriate notched trowel. Avoid excessive adhesive thickness by passing the trowel evenly through the adhesive at a 45 degree angle. Observe the appropriate flash time (if applicable). Lay the flooring into the adhesive, correctly position it and press down firmly. Be sure to check the back of the flooring to make certain good adhesive transfer from sub floor to flooring is achieved. Roll flooring approx. 15-30 min after installation with a 35# roller for double glue and 75-100# roller for sheet vinyl if recommended by the flooring manufacturer. Push down raised edges approx. 30-60 min after installation.
Storage
Store and transport protected from freezing. Recommended minimum temperatures are 35 °F for transport and 40 °F for storage. Do not stir product if frozen, allow to thaw completely.
Limitations
When using other than STAUF products in conjunction with STAUF primers, sealers, leveling compounds, or adhesives, STAUF denies any and all responsibility for any ensuing problems and/or damages without prior written authorization from STAUF.
In case of accident, injury, spill or exposure, see SDS sheet for information. Consult technical data sheet at www.staufusa.com for updated information.
This adhesive will maintain its integrity and performance even when higher levels of moisture are present. While adhesive can withstand up to 8#/24 hrs/1,000 SF (Calcium Chloride Test) and 85% RH (in-situ probe) of moisture, it does not qualify as a moisture inhibitor. Please see below for recommended sealers if a moisture barrier is required. Not suitable for areas with excessive topical moisture (i.e. melting snow, repeated flooding, pressure washing) or extreme horizontal shear forces; use R-Series adhesives under these circumstances.
The foregoing representations are based on the results of our most current product and material testing within a controlled environment and are of a non-obligatory advisory nature only. As such, they do not constitute an express or implied warranty of any kind including the Warranty of Merchantability and/or Fitness for a Particular Purpose. Because we have no control over the actual quality of workmanship, materials used and worksite conditions, STAUF USA, LLC. will in no event be liable for any incidental and/or consequential damages. herefore, we strongly recommend that prior on-site testing be conducted to refer to and study the suitability of the product for the intended purpose. With the release of this technical information sheet all its prior versions become invalid. For warranty and warranty disclaimer information please see our Limited Lifetime Warranty @ www.staufusa.com
General Features
  • LEED qualified
  • contains no VOC (calc. per CA Rule 1168)
  • nonflammable
  • dispersion base cleans with water
  • certified "green", CRI GLP
Installation Features
  • very low odor
  • cleans with warm water and soap
  • spreads easily
  • dries quickly
  • higher temp will shorten drying time
Long Term Features
  • resistant against aging
  • remains elastic
Approved Flooring
  • Carpet (attached cushion)
  • Carpet (felt, fiber, jute, woven vinyl)
  • Carpet (latex unitary, urethane cushion, hot melt and other commercial backings)
Approved Sub Floors
  • Concrete Slabs
  • OSB (underlayment grade)
  • Plywood (underlayment grade)
  • Felt backed Sheet Vinyl (well bonded, sanded, asbestos-free)
  • Cured Leveling Compounds
  • VCT (well bonded, sanded, asbestos-free)
  • (do not install non-porous flooring over non-porous sub floors)
Flash Time (wet lay)
  • 10 - 20 min
Open Time (wet lay)
  • 45 - 60 min
Approved Primers
  • Primer is normally not required
  • STAUF AQP-200 Eco-Prime
Approved Sealers
  • STAUF ACS-210 True-Seal
Approved Leveling Compounds
  • STAUF SLC-540 Self Leveling Compound
  • STAUF QFF-560 Quick Feather Float
  • STAUF RLC-580 Fiber Level
Approved Trowels and Spread Rate
  • Unitary and double-glue-#6 (1/8"x1/8"x1/16" U notch): up to 100 SF/gal.
  • Woven Polypropylene-#7 (1/8"x1/8"x1/8" U notch): up to 100 SF/gal
  • Attached cushions-#15 (3/32"x3/32"x3/32" V notch): up to 130 SF/gal.
Cure Time until Normal Traffic
  • approx. 24 hours
Clean-Up
  • Use soap and water
Temperature Range during Installation
  • 50-90F
Relative Humidity Range during Installation
  • 30% - 80%
Packaging Size
  • 4 gal. Plastic Pail
  • 48 per pallet
Color
  • Cream
pH value of concrete
  • must be between 7 and 9
Transportation
  • above 35F (do not stir if frozen, allow to thaw completely)
Storage
  • above 40 F, protect from freezing
Shelf Life
  • 12 Months in original, unopened container
Revision: 2017-09-19 12:15:35

Please enter the email address of the person to whom you would like to send this PDF.